TZB-info / Heating / Measurement and control / The most used sensors of the German manufacturer S + S RegeltechnikDomat Control System sro is a Czech manufacturer of freely programmable controllers for building management systems and the exclusive distributor of S + S Regeltechnik peripherals in the Czech and Slovak Republics.Domat has currently prepared a special offer of selected most used sensors from the German manufacturer S + S Regeltechnik.The special offer of the S + S Regeltechnik brand includes stem temperature sensors TF43 with stem length from 50 to 300 mm, external IP43 protection and accessories, attached temperature sensors with passive output ALTF02, cable sensors HTF50, room, duct and wall humidity sensors and temperatures, KW condensation sensors, DF differential pressure sensors, DS-205 differential pressure switches and KCO2 channel sensors.Stem temperature sensors are now more flexible.Duct sensors for measuring the temperature in the ventilation duct and well ("immersion") sensors for measuring the temperature of liquid media are manufactured in the same design as one type under the designation TF43 ..., the type of measuring element and the length of the sensor in five sizes 50 to 300 mm.A plastic flange with an MF fixing screw is supplied as a separate accessory for installation in the air duct.TH08-VA.All you have to do is have fewer types of sensors on hand and add accessories depending on where they are installed.The case is polyamide, the cover can be easily removed and put on.Screw terminals guarantee safe signal transmission.ALTF02 sensors are a cheaper alternative for small-diameter pipes, where it is not possible to install welds for sumps, or less demanding applications, such as equithermal circuits.HTF cable sensors are used for places with cramped installation or temperature measurement in concrete floors.These can be used in silicone-insulated versions up to temperatures of 180 ° C.Other sensors in action are duct, room and wall combined temperature and humidity sensors (RF ..., AF ..., KF ...) together with a condensation and dew point sensor KW for use in cooling ceiling systems, where they serve both for active protection against condensation, as well as limiting elements.Differential pressure sensors DF ... are used in clean rooms and VAV / CAV systems.They have a switchable range up to 0001000 ... 1000 or −5000 ... 5000 Pa and thus simplify design.Some types are equipped with a display, so the measured values can be read directly at the measuring probes, which greatly simplifies commissioning and service.The KCO2 channel carbon dioxide sensor is now available in a new housing, which simplifies and clarifies installation.CO2-controlled air handling units help save energy and operating costs.The sensor has switchable ranges: 0 ... 10 V corresponds to a concentration of 0 ... 2000 ppm or 0 ... 5000 ppm.Domat has a new advantage offer of the most frequently deployed sensors by the German manufacturer S + S Regeltechnik.On the top of the list there are stem temperature sensors TF43 with stem length 50 to 300 mm, protection degree IP43 and accessories, strap-on temperature sensors with passive output ALTF02, cable sensors HTF50, room, duct and wall temperature and humidity sensors, condensation sensors KW, differential pressure sensors DF, differential manostats DS-205, and duct sensors KCO2.The stem temperature sensors are more flexible now.Both the duct sensors for measuring of temperature in an air duct and pocket (or immersion) sensors for fluid media are produced in the same design as a single type, TF43 .... Further on, the measuring element type and sensor length in five sizes from 50 to 300 mm are specified.To install the sensor in an air duct use MF, a plastic flange with a fixing screw, which is supplied as a separate accessory.For installation as an immersion sensor there are brass or stainless steel pockets TH08-MS and TH08-VA respectively.Less sensor types can be on store then, completed by the accessory according to the installation type.The sensor have polyamide housing with glass fiber reinforcing, the cover can be removed and put back easily.Proven screw terminals make sure that the signal will be safe.The strap-on sensors ALTF02 are budget alternative for piping of small diameters where it is impossible to use welded-on pieces for pockets, or for less critical applications, like weather-compensated heating circuits.For complicated installation or temperature measuring in concrete floor systems, cable sensors HTF are used.The silicone cable option can be used for temperatures up to 180 ° C.Other featured sensors are duct, room and wall combined temperature and humidity sensors (RF ..., AF ..., KF ...) together with condensation and dew point sensor KW for cooling panels.They are used as active protection against condensation as well as limitation sensors.Differential pressure sensors DF ... are used in clean rooms and VAV / CAV systems.Their variable range of up to −1000 ... 1000 or −5000 ... 5000 Pa makes technology design easy.An optional LCD display enables reading the measured values directly at the probes, which speeds up commissioning and service.The carbon dioxide duct sensor KCO2 is now supplied in a new housing for easier installation.Air handling units controlled according to CO2 help saving energy and operation costs.The sensor has selectable ranges: the 0 ... 10 V output can be set as 0 ... 2000 ppm or 0 ... 5000 ppm.Domat Control System sro is a Czech producer of freely programmable controllers for building control systems, and exclusive distributor of S + S Regeltechnik peripherials in the Czech and Slovak Republic.Domat Control System sro belongs to the top European suppliers of control systems and regulations for intelligent buildings, industry and energy.The goal of this purely Czech company is to develop, manufacture and supply control systems on an international scale.